My name is Andy Spoone. In this video, we are going to take a look at an LRC setup with PASCO Capstone and the 850 Universal Interface. Let's begin by taking a look at our LRC circuit setup. Inazuma eleven go sub indo full.

• Keygen Software

PASCO Capstone is the next leap forward in software for data acquisition, display and analysis and destined to be the new standard in advanced physics and engineering labs. Not an upgrade on existing software, PASCO Capstone was built from the ground up to be the most powerful and flexible option available. Icare Data Recovery Software Key Serial Pasco Capstone; Easy Drive Data Recovery 3.0 Registratio 321soft Data Recovery Serial Key For Mac Icare Data Recovery Software Key Serial Aqua Data Studio 6.0.15 Serial Number; Stellar Phoenix Cd Dvd Data Recovery 5 S Stellar Phoenix Cd Dvd Data Recovery V5 Tellar Phoenix Cd Dvd Data. Tips and interesting applications using PASCO sensors, software and equipment. Have innovative lab ideas you'd like to share? We'd love to hear from you! PASCO Capstone. Version: 1.11.1 Released 3/2/2018. Free Trial Update. PASCO Capstone User's Guide. Free Experiments. SPARKvue Version: 3.1.3 Released 3/28/2018.

I am going to be using the UI-5210 circuit board. On the circuit board I am going to be using the first inductor component, the first capacitor component, and the second resistor component. Connected to my 850 interface, in Channel A I have a Voltage Sensor measuring the voltage across the entire circuit. In Channel B, I have a Voltage Sensor measuring the voltage across my second resistor. And my signal generator is attached across the entire circuit.

Now let's take a look PASCO Capstone and getting set up inside of our software. I am going to begin by going to my Hardware Setup and adding my two Voltage Sensors. I can do that by clicking on the channel, typing the first few letters of the sensor, and then confirming it with the Enter button. So I am going to add my two Voltage Sensors. I am now ready to go set up my signal generator. So I am going to click on my Signal Generator, and I will be using Output 1. I am going to create a single sweep sine wave that's going to be looking at a range of frequencies across the circuit, hoping to find the resonating frequency for the LRC setup somewhere approximately in the middle of my time range.

So let's go and turn on the single sweep. We are going to be using an amplitude of 3 V. We are going to start our initial frequency at 1000 Hz, our final frequency is going to be at 70000 Hz, over a duration of 25 seconds, in steps of 1 Hz.

Once your signal generator is set up, we can now go ahead and pin that to our screen, and open up a full-screen Scope beside it. So let's go ahead and get our Scope set up.

I am going to begin by adding Channel A to my left axis. I am going to insert a second y-axis and add my Channel B Voltage Sensor. I am going to go ahead and turn on my trigger. This will trigger on voltage from Channel A. I am also going to go ahead and adjust my axis. So I know that my amplitude max is 3 V. So I am going to go ahead and adjust both of my y-axis ranges so that they max out near 3 V.

I am also going to go ahead and adjust my time axis. Now notice whenever I start adjusting my time axis, my sample rate is automatically changing along with it. And what Capstone is trying to do is adjust the sample rate, so you are getting the maximum number of points to fill up your oscilloscope display. Now for this particular set up, I am going to be using components that are resonating approximately around 30-35000 Hz. So I am going to go and get a sample rate of approximately 5 MHz. So, as you can see -- approximately there -- I am at a scale of 0 to 0.00008 seconds.

So that's approximately the scale I am going to be using. The last thing I want to do is change my Record mode from Continuous to Fast Monitor. This will change the Record button to a Monitor button. I am now ready to begin monitoring my voltages, so I am going to press the Monitor button, and I am going to turn my signal generator on.

Keygen Software

You'll notice that I instantly have two different waves that come in to view in my oscilloscope. They begin out of phase with each other. As I approach the resonating frequency, they go in to phase. As I go beyond the resonating frequency, they go out of phase with each other, and my amplitudes begin to decrease. And we will just wait a second and watch the signal generator run through the entire 25 seconds. Afterwards there is no signal produced, so you shouldn't see anything in your oscilloscope.

But they cant stop what im bringing cant stop what im bringing.

So let's go ahead and turn off our signal generator and stop our monitoring. I'm going to run through that one more time. And this time I am going to try to stop it approximately where the resonating frequency is. So let's begin monitoring and turn it on. And right as the waves come right in phase with each other, I am going to try to stop it.